|
1 | | In ATM, end devices such as routers use all _____ layers, while switches inside the ATM network use only the bottom ______layers. |
| | A) | two; three |
| | B) | three; two |
| | C) | one; two |
| | D) | none of the above |
|
|
2 | | The only AAL used by the Internet is __________. |
| | A) | AAL1 |
| | B) | ALL3/4 |
| | C) | AAL5 |
| | D) | none of the above |
|
|
3 | | AAL5 is sometimes called the _________. |
| | A) | SAL |
| | B) | SEAL |
| | C) | SEL |
| | D) | none of the above |
|
|
4 | | AAL5 accepts an IP packet of no more than 65,536 bytes and adds _________ in addition to padding. |
| | A) | one trailer |
| | B) | one header |
| | C) | both a and b |
| | D) | none of the above |
|
|
5 | | The ________ layer provides routing, traffic management, switching, and multiplexing services. |
| | A) | AAL |
| | B) | ATM |
| | C) | both a and b |
| | D) | none of the above |
|
|
6 | | When we use IP over ATM, only the ________ cell carries the 8-byte trailer added to the IP datagram. |
| | A) | last |
| | B) | first |
| | C) | both a and b |
| | D) | none of the above |
|
|
7 | | When we use IP over ATM, padding can be added only to the _____ or the _______. |
| | A) | first cell; last cell |
| | B) | last two cells; last three cells |
| | C) | last cell; last two cells |
| | D) | none of the above |
|
|
8 | | To find the physical address of the exiting-point router, ATM uses the services of _________. |
| | A) | ARP |
| | B) | IP |
| | C) | ATMARP |
| | D) | none of the above |
|
|
9 | | The inverse request and inverse reply messages can bind the physical address to an IP address in a(n) _______ situation. |
| | A) | SVC |
| | B) | PVC |
| | C) | both a and b |
| | D) | none of the above |
|
|
10 | | The request and reply message can be used to bind a physical address to an IP address in a(n) _______ situation. |
| | A) | SVC |
| | B) | PVC |
| | C) | both a and b |
| | D) | none of the above |
|
|
11 | | The inverse request and inverse reply can also be used to build the server _______ table. |
| | A) | mapping |
| | B) | routing |
| | C) | both a and b |
| | D) | none of the above |
|
|
12 | | __________ allows an ATM network to be divided into several logical subnets. |
| | A) | LAS |
| | B) | LAN |
| | C) | LIS |
| | D) | none of the above |
|
|
13 | | A router connected to an ATM network uses the _______ layers. |
| | A) | AAL and ATM |
| | B) | AAL and physical |
| | C) | AAL, ATM, and physical |
| | D) | none of the above |
|
|
14 | | A switch inside an ATM network uses the _______ layers. |
| | A) | AAL and ATM |
| | B) | AAL and physical |
| | C) | ATM and physical |
| | D) | none of the above |
|
|
15 | | Which ATM layer adds an 8-byte trailer to an IP packet? |
| | A) | AAL5 |
| | B) | ATM |
| | C) | physical |
| | D) | none of the above |
|
|
16 | | Which ATM layer has a 53-byte cell as an end product? |
| | A) | physical |
| | B) | ATM |
| | C) | AAL5 |
| | D) | none of the above |
|
|
17 | | The VPI of a UNI is _______ bits in length. |
| | A) | 8 |
| | B) | 12 |
| | C) | 16 |
| | D) | none of the above |
|
|
18 | | The VPI of an NNI is _______ bits in length. |
| | A) | 8 |
| | B) | 12 |
| | C) | 16 |
| | D) | none of the above |
|
|
19 | | The _______ field of the ATM header provides error control. |
| | A) | CLP |
| | B) | HEC |
| | C) | VPC |
| | D) | none of the above |
|
|
20 | | A datagram of 1010 bytes needs _______ bytes of padding. |
| | A) | 0 |
| | B) | 38 |
| | C) | 46 |
| | D) | 48 |
|
|
21 | | A datagram of 402 bytes is divided into _______ cells. |
| | A) | 6 |
| | B) | 7 |
| | C) | 9 |
| | D) | none of the above |
|
|
22 | | The maximum amount of padding that can be added is _______ bytes. |
| | A) | 0 |
| | B) | 47 |
| | C) | 48 |
| | D) | none of the above |
|
|
23 | | When a _______ exists between two routers on an ATM network, an ATMARP server is not needed. |
| | A) | permanent virtual circuit |
| | B) | switched virtual circuit |
| | C) | logical IP subnet |
| | D) | none of the above |
|
|
24 | | What is the first step in establishing a virtual connection on an ATM network? |
| | A) | connecting to an ATMARP server |
| | B) | connecting to the exiting-point router |
| | C) | formation of a logical IP subnet |
| | D) | none of the above |
|
|
25 | | How can two routers be connected on an ATM network? |
| | A) | through a PVC |
| | B) | through an SVC |
| | C) | a and b |
| | D) | none of the above |
|